Where Runoff Concentrates on Texas Farm Fields

Find the draws and swales where water from the ground above comes together, from public lidar, and take the map to your soil and water conservation district or NRCS field office.

Rain that runs off a field does not leave it evenly. Water runs downhill and gathers in the low lines of the ground: a swale across a cotton or corn field, a draw at the bottom of a pasture, the corner where a field road meets the fence. NRCS calls that concentrated surface flow, and it is the condition one of its conservation practice standards is written for.

The Texas State Soil and Water Conservation Board’s nonpoint source program page puts the stakes plainly: nonpoint source pollution “occurs when rainfall flows off the land, roads, buildings, and other features of the landscape,” and “this diffuse runoff carries pollutants into drainage ditches, lakes, rivers, wetlands, bays, and aquifers.” Among the common pollutants it lists: “Fertilizers, herbicides, and insecticides from agricultural lands and residential areas” and “Sediment from construction sites, crop and forest lands, and eroding stream banks.”

The USDA Natural Resources Conservation Service (NRCS) publishes conservation practice standards. Its Grassed Waterway standard (Code 412) defines the practice as “a shaped or graded channel that is established with suitable vegetation to convey surface water at a nonerosive velocity using a broad and shallow cross section to a stable outlet,” and says it is applied “in areas where added water conveyance capacity and vegetative protection are needed to prevent erosion and improve runoff water quality resulting from concentrated surface flow.” Among its listed purposes: “Prevent gully formation.”

NRCS’s overview of the practice adds that waterways “are constructed to convey runoff from concentrated-flow areas, terraces, or diversions where erosion control is needed,” and ends: “For further information, contact your local NRCS field office.”

So the first question on the ground is a terrain question: where does the water come together? That part you can map from your desk.

Map it in seven steps

  1. Select the field. Open Property and click the field to use its parcel boundary as the working area, or take up to 25 parcels at once for a whole farm. Where the parcel map has a gap, or you want one field only, draw a box or polygon instead. Open it on the map · How it works
  2. Map the flow paths. Run Water & Drainage. Thicker, paler lines drain more land, and tapping any line shows the acres upstream of it. A field where several faint paths join into one strong one is a field where runoff concentrates; the joins and the draw below them are the places to look at first. The terrain loaded reaches beyond your boundary, so water arriving from a neighbor’s ground or the road is counted. Open it on the map · How it works
  3. Check where water sits. Switch to the Ponding view to see the hollows that would hold water once full, with their depth, area and volume. Real hollows drain into the soil and evaporate, so these are upper bounds. A long strip of ponding along a county road usually means a culvert the lidar cannot see. Open it on the map · How it works
  4. Follow water from one spot. Open Downhill Path and click a spot, such as a barnyard, a manure stack or the top of a draw. The line shows where rain from there runs, and the panel says how far it goes before it joins a water path, becomes a watercourse or reaches a stream. Open it on the map · How it works
  5. See the land draining to a point. Open Catchment and click the bottom of a draw or the corner where water leaves the field. The blue area is all the land that drains there, in acres. If much of it lies outside your boundary, the water in that draw is partly someone else’s runoff, which is worth knowing before you talk to your district or NRCS. Open it on the map · How it works
  6. Read slope and wet ground alongside. Slope & Aspect shows how steep the ground above each draw is, and Wetness Map ranks the field from dry ground to the flats and hollows where the shape of the land concentrates water. Neither is a soil or wetland map; they are the terrain half of the picture. Open it on the map · How it works
  7. Look back through old photos. Aerial History steps through every year of aerial photos TxGIO holds for a spot, 1981 to 2022. Swipe between them to look for old roads, filled ditches or a stream that has moved. Open it on the map · How it works

Map the flow paths on your field

Select the parcel or draw a box, and run Water & Drainage. Free to use, no account.

Open Water & Drainage →

What the map can and can’t tell you

The flow paths are traced from the USGS 3DEP bare-earth lidar model: each cell passes its water to its steepest neighbor and the land upstream of every cell is added up. That is a good picture of where the surface sends water. It is not the whole picture:

  • No soil, erosion or nutrients. The tools do not model what runoff carries. EPA notes that producers “can adopt soil and water conservation practices to reduce the runoff of sediment, nutrients, bacteria, pesticides, and other pollutants from their operations,” and that the effects of runoff “vary widely, depending on the type of operation, landscape conditions, soils, climate, and farm management practices.” The terrain is one of those; the rest is on the ground. For soils, NRCS’s Web Soil Survey provides soil data and information.
  • No tile, drains or culverts. Tile lines, culverts and ditches narrower than the sampling are not in the lidar. Draw the ones you know under Culverts & barriers.
  • The ground on the day it was flown. Leveling, terraces and ditches built since the lidar survey do not show. Data Here lists which surveys cover a spot and when they were flown.
  • No design. Nothing here lays out or engineers a practice. The 412 standard itself says to plan, design and construct grassed waterways “to comply with all Federal, State, and local laws and regulations,” and NRCS’s Grassed Waterway page says national standards should not be used to plan, design or install a practice, pointing instead to the Field Office Technical Guide.

Who to take the map to

  • Your soil and water conservation district. The Texas State Soil and Water Conservation Board (TSSWCB) describes itself as “the state agency that administers Texas’ soil and water conservation law and coordinates conservation and nonpoint source water pollution abatement programs throughout the State,” and says that soil and water conservation districts (SWCDs) manage “a variety of local conservation activities across the state.” Its home page has an SWCD locator map. A district is also where a water quality management plan starts: the TSSWCB says such a plan is “developed through and approved by soil and water conservation districts for agricultural or silvicultural lands.”
  • Your NRCS field office. Start from NRCS’s Texas state office page, where NRCS describes its conservation technical assistance as helping producers “identify conservation objectives and a roadmap for conservation on their operation,” or find your local USDA Service Center with the farmers.gov service center locator.
  • The TSSWCB, for the state programs. Its Texas Nonpoint Source Management Program page says the program is jointly administered by the TSSWCB and the Texas Commission on Environmental Quality (TCEQ). Ask them what applies to your operation; this site does not interpret any rule.

What to bring: the flow path map with the acres on the main draws, the catchment of each draw you are asking about, and the slope map. The property report’s data ZIP can hold a slope map, the flow paths, a wetness map, contours and an aerial photo for the parcel in one download (parcel boundaries are not included in the files).

Go further

Every tool runs free on the map. Files for your district’s or NRCS’s GIS need a pass.

Related guides

Frequently asked questions

How do I find where runoff concentrates in my field?

Select the field on the map, as a parcel or a box you draw, and run Water & Drainage. Each flow path is labeled with the acres of land draining through it, so the draws where paths join and the figure climbs are where water from the ground above comes together. Walk those spots, ideally during or just after a heavy rain, to see what the water actually does there.

Can this tell me where to put a grassed waterway?

It shows where concentrated flow is, which is where NRCS’s Grassed Waterway standard (Code 412) says the practice applies. Whether a waterway or another practice fits, and how it is laid out and built, is a question for your soil and water conservation district or NRCS field office: NRCS notes that its national practice standards should not be used to plan, design or install a practice, and points to the Field Office Technical Guide for the local version. The maps help that conversation; they do not replace it.

Does the map know about my tile drains, culverts and ditches?

Not unless you draw them. Water is routed over the surface of the lidar ground model, so a culvert under a farm road, a tile line or a narrow ditch is invisible to it. Draw them under Culverts & barriers in Water & Drainage and run again; the result says when your lines were used.

Does it show erosion or nutrient loss?

No. It shows where the ground sends water and where water would sit. It does not model erosion, sediment, nutrients or soil. For soils, NRCS’s Web Soil Survey provides soil data and information; for what runoff carries from a particular field, ask your soil and water conservation district.

What is a water quality management plan?

The Texas State Soil and Water Conservation Board (TSSWCB) describes a water quality management plan (WQMP) as a site-specific plan developed through and approved by soil and water conservation districts for agricultural or silvicultural lands. Ask your district or the TSSWCB what applies to your operation. This site does not interpret any rule.

Is it free?

Running every tool on the map is free, with no account. Downloading the flow paths, catchment outlines and grids as files needs a pass.

Sources

About the data

Ground elevations come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model, with elevations above NAVD 88. Source cells are 3.3 ft per pixel in the finest work units, with about 9.8 ft per pixel and 33 ft per pixel sources elsewhere. USGS elevation data is public domain. Lidar coverage and source dates vary across Texas. Check your site against the USGS 3DEP work-unit index; an unavailable lookup means coverage is unknown. More from the USGS 3D Elevation Program and Texas elevation and lidar resources.